Sika AnchorFix 1 300 ml
    Sika AnchorFix 1 300 ml

Sika AnchorFix 1 300 ml

Reference: 0.38.157.044

In stock 1-3 Working Days
€19.16
Tax included

2-component, styrene- and solvent-free, polyester based anchoring material

Quantity

Description

Sika AnchorFix 1 Anchor Adhesive

2-component, styrene- and solvent-free, polyester based anchoring material

Advantages

  • Fast ripening
  • Applied with a regular hand gun for ampoules
  • Used at low temperatures
  • High load bearing capacity
  • EDF approved for anchorages in non-cracked concrete
  • EDF approved for solid and hollow masonry
  • Does not slip even in ceiling applications
  • Styrene free
  • Light odor
  • Reduced hardware loss

Features

  • Density ~1.63 kg/l (A+B mixture of ingredients)
  • Compressive strength ~60 N/mm2 (7 days, +20 °C)
  • Compressive elasticity measure ~3 500 N/mm2 (7 days, +20 °C)
  • Tensile bending strength ~28 N/mm2 (7 days, +20 °C)
  • Tensile strength ~12 N/mm2 (7 days, +20 °C)
  • Operating temperature Long-term -40 °C minimum / +50 °C maximum Short term (1-2 hours) +80 °C
  • Sika AnchorFix 1 Anchor Adhesive
  • 2-component, styrene- and solvent-free, polyester based anchoring material

Advantages

  • Fast ripening
  • Applied with a regular hand gun for ampoules
  • Used at low temperatures
  • High load bearing capacity
  • EDF approved for anchorages in non-cracked concrete
  • EDF approved for solid and hollow masonry
  • Does not slip even in ceiling applications
  • Styrene free
  • Light odor
  • Reduced hardware loss

Features

  • Density ~1.63 kg/l (A+B mixture of ingredients)
  • Compressive strength ~60 N/mm2 (7 days, +20 °C)
  • Compressive elasticity measure ~3 500 N/mm2 (7 days, +20 °C)
  • Tensile bending strength ~28 N/mm2 (7 days, +20 °C)
  • Tensile strength ~12 N/mm2 (7 days, +20 °C)
  • Operating temperature Long-term -40 °C minimum / +50 °C maximum Short term (1-2 hours) +80 °C

Application

  • Preparing the ampoule: Unscrew the cap, cut off the protective tape, screw on the static mixer, insert the ampoule into the gun and start applying
  • When work is stopped, the stationary mixer can remain in the ampoule, after the piston pressure is released
  • Upon resumption of work, in case the resin has hardened inside the static mixer, it should be replaced
  • Removal of fresh debris from tools and application equipment can be carried out using Sika Colma
  • Hardened and/or matured material (adhesive) can only be removed mechanically
  • Mixing ratio Component A: component B = 10 : 1 by volume
  • Layer thickness 3 mm maximum
  • Hanging flow Does not sag, even in ceiling applications
  • Product temperature Sika AnchorFix 1 must have a temperature between +5°C and +40°C to be applied
  • Ambient temperature: -10 °C minimum / +40 °C maximum
  • Dew point Beware of condensation! The substrate during application must have a temperature of at least 3 °C above the dew point
  • Substrate temperature: -10 °C minimum / +40 °C maximum  

Data sheet

Container
300 ml
Brand Name
SIKA

3 other products in the same category:

Product added to compare.